|
NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.
Carpet floor mat
| | |
 | Carpet floor mat |
Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.
Foot throttle kit
| | |
 | Foot throttle next to pedals |
|  | BRE10440 foot throttle kit |
| The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.
Foot decelerator kit
| | |
 | Foot decelerator next to pedals |
|  | BXX10810 foot decelerator kit |
| The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.
Footrests
| | |
 | BRE10458 footrest kit with three pegs |
|  | Foot peg on the steering column |
| The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.
The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.
Features:
- Direct bolt-on factory finish – no drilling or cutting required
- Heavy gauge steel to support any operator
- Color-matched rubber surfaces for comfort and vibration reduction
- Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)
Sun shade
| | |
 | RE593670 sun shade shown |
The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.
Storage container with lid/ashtray
| | |
 | RE275532 storage container |
|  | Storage container mounting location |
| This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.
Leather-wrapped steering wheel
| | |
 | RE584990 leather steering wheel |
|  | Close-up of leather steering wheel |
| Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.
Refrigerator
| | |
 | Refrigerator |
|  | Keep food and drinks cool with refrigerator |
| The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.
Rearview mirror (internal)
| | |
 | RE588734 internal rear mirror (shown in standard mounting position) |
The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.
Cab power inverter
| | |
 | Type A/B style socket inverter kit (type C style is similar) |
|  | Cab power inverter kit |
| These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update.
| | |
Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins) |
|
 | RE596958 complete John Deere power strip for model year 2020 and newer cabs |
The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.
| | |
Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter |
|
 | RE596959 power adapter |
For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.
A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.
| | |
Harness adapter for citizen band (CB) power connection |
|
 | Antenna coax and power connector base prewired in the cab |
|  | Harness adapter for power connection |
| Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.
Amp-to-flying leads power connector
| | |
 | RE37651 power connector |
This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.
Amp-to-John Deere power outlet adapter
| | |
 | RE67015 outlet adapter |
This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.
External StarFire™ mounting bracket
| | |
 | StarFire mounting bracket |
The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.
Front license plate mounting bracket
| | |
 | License plate mounting bracket (front) |
This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.
Vandal protection door locks with custom key
| | |
 | R569171 door lock handle |
Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.
Joystick (multifunction lever)
| | |
 | BRE10436 multifunction lever (shown in model year 2018 7R Tractor) |
This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.
Subwoofer and tweeter kit
| | |
 | Subwoofer |
|  | Tweeters |
|  | Amplifier |
| Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.
The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.
Touchscreen radio relocation kit
| | |
 | BRE10364 touchscreen radio relocation kit |
Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.
Features:
- Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
- Fine-tune the position adjustment with the locking knob on the tie rod
Touchscreen video camera upgrade kit
| | |
 | Touchscreen video camera upgrade kit |
Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.
NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.
| | |
  |
Code | Attachment | Description |
| RE581987 | Carpet floor mat Cut specifically for the large front area of the cab and does not include the areas on the sides of the operator seat. NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX and model year 2022 9R/9RX (with CommandView 4 cab) regardless of foot throttle option. |
| BRE10440 | Foot throttle kit Controls engine rpm with right foot. Mounts directly to the center console on the right side. NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX and model year 2022 9R/9RX (with CommandView 4 cab). NOTE: Compatible with carpet floor mat RE581987 without modifications. NOTE: See installation instructions (RE590867). |
| BXX10810 | Foot decelerator kit
Slows ground speed with engine throttle without adjusting set speed NOTE: Compatible with model year 2022 and newer 9R/9RT/9RX.
NOTE: Compatible with carpet floor mat RE581987 without modifications.
NOTE: See installation instructions (TR122199).NOTE: Not compatible with orange foot-operated speed control kit BRE10440. |
| BRE10458 | Footrests Adds three pegs to the standard cab. NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX and model year 2022 9R/9RT/9RX (with CommandView 4 cab).
NOTE: See installation instructions (R567350). |
| RE593670 | Sun shade Adds a sun shade to right and/or rear window locations. NOTE: Also order two cap screws (L175903). NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX and model year 2022 9R/9RT/9RX (with CommandView 4 cab). |
| RE275532 | Container with lid/ashtray Heavy plastic cup with hinged lid and foam seal. Keeps ash, snacks, or small items well contained. NOTE: Compatible with nearly all John Deere cabs including the model year 2020 7R and 8R/8RT/8RX and model year 2022 9R/9RT/9RX (with CommandView 4 cab) smaller cup holder at mid-window. |
| RE584990 | Leather-wrapped steering wheel Upgrades the standard steering wheel to a leather-wrapped steering wheel. NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX and model year 2022 9R/9RT/9RX (with CommandView 4 cab). NOTE: Existing hardware from the standard steering wheel can be reused for installation. |
| RE593672 | Refrigerator Adds the same refrigerator unit inside the storage compartment behind the instruction seat. NOTE: Also order heating, ventilation, and air conditioning (HVAC) plug (R562501) and seal (R566287). Note: Compatible with model year 2020 7R and 8R/8RT/8RX and model year 2022 9R/9RT/9RX (with CommandView 4 cab) Select Comfort and Convenience package cabs. |
| RE588734 | Internal rearview mirror Adds a second internal rearview mirror to the left side of the cab which is identical to the right-side mirror. NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX and model year 2022 9R/9RT/9RX (with CommandView 4 cab). NOTE: Also order two cap screws (R132206). |
| BRE10452 | 120-V AC power inverter Type B style socket with 120-V AC/60 Hz/300 W. NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX model year 2022 9R/9RT/9RX (with CommandView 4 cab). NOTE: See installation instructions (R566797). |
| BRE10453 | 230-V AC power inverter Type C style socket with 230-V AC/50 Hz/300 W. NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX model year 2022 9R/9RT/9RX (with CommandView 4 cab). NOTE: See installation instructions (R566797). |
| RE596958 | Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins) Adds the complete power strip into the cab which connects to a single amp-style connector. NOTE: Approved for mounting to R558980 (headliner mounting rail), BRE10574 (right-side window mounting bracket and rail), or BRE10575 (short vertical mounting rail). John Deere recommends using the following mounting hardware with the previous mounting options: two 21M7577 screws, two options R77391 washers, and two 14M7303 flanged nuts. NOTE: Compatible with model year 2020 and newer 7R and 8R/8RT/8RX model year 2022 9R/9RT/9RX (with CommandView 4 cab). NOTE: Limits total power consumption from all accessory power points of the cab to less than 30 amps. |
| RE596959 | Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter Converts one powered device from the three-pin octagonal connection type to three-pin round style connector in the base cab. NOTE: Compatible with model year 2020 and newer 7R and 8R/8RT/8RX model year 2022 9R/9RT/9RX (with CommandView 4 cab). NOTE: This style is typically not used in European countries, where RE596960 is preferred. NOTE: Limits total power consumption from all accessory power points of the cab to less than 30 amps |
| RE596960 | Three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter Converts one powered device from the three-pin octagonal connection type to three-pin round style connector in the base cab. NOTE: Compatible with model year 2020 and newer 7R and 8R/8RT/8RX model year 2022 9R/9RT/9RX (with CommandView 4 cab). NOTE: This style is typically preferred in European countries. All other locations use RE596959. NOTE: Limits total power consumption from all accessory power points of the cab to less than 30 amps. |
| RE597710 | Three-pin connector with flying leads Allows open ended wires to be connected to any aftermarket three-wire, 12-V radio and then connected directly into the designated cab harness point included in base. NOTE: Limits total power consumption from all accessory power points of the cab to less than 30- amps. |
| RE37651 | Amp-to-flying leads power connector Adds the amp-style, three-socket power connector to a display harness. NOTE: This is a single-sided connector with three flying wire leads; requires user to fuse wires together from another harness like an aftermarket display. NOTE: Compatible with monitors and displays which use a three-wire power harness. NOTE: Compatible with R-Series and newer tractors. |
| RE67015 | Amp-to-John Deere power outlet adapter Provides a double-sided connector adapter for going from an amp three-socket power connector to a John Deere power strip style socket. NOTE: Compatible with monitors and displays which use a three-socket amp connector. NOTE: Compatible with 00 Series, 10 Series, 30 Series, and up to model year 2019 R-Series Tractors with John Deere power strip. |
| RE588540 | External StarFire mounting bracket Provides a mounting provision for StarFire 3000 and StarFire 6000 Receivers. NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX and model year 2022 9R/9RT/9RX (with CommandView 4 cab). NOTE: Compatible with front license plate mounting frame (RE589515). NOTE: Also order one mounting hoop (PF81190) and eight cap screws (L157372). NOTE: Adding the external StarFire receiver will increase the total rigid height of the tractor. |
| RE589515 | Front license plate mounting bracket Adds a license plate mounting bracket to the front of the vehicle where a license or permit can be mounted to fufill local on-road requirements. NOTE: Compatible with RE88540. NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX and model year 2022 9R/9RT/9RX (with CommandView 4 cab). NOTE: Adding the front license plate mounting bracket does not increase the total height of the tractor. |
| R569171 | Vandal protection door locks with custom key Kit contains one door handle with unique lock cylinder and two matched keys that are a different tooth style than what is used in the ignition switch. NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX model year 2022 9R/9RT/9RX (with CommandView 4 cab). NOTE: See installation instructions (R569172). |
| BRE10436 | Single-lever multifunction joystick NOTE: Not configurable with sixth SCV position (BRE10124, BRE10049). NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX and model year 2022 9R/9RT/9RX (with CommandView 4 cab). NOTE: See installation instructions (R566260). |
| BRE10451 | Subwoofer and tweeter kit Includes subwoofer, two tweeters (with matching interior grilles), amplifier, and hardware. NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX model year 2022 9R/9RT/9RX (with CommandView 4 cab) Select cab package single DIN Delphi radio. NOTE: See installation instructions (R466796). |
| BRE10364 | Remote-mounted display for touchscreen radio NOTE: Compatible with model year 2020 7R and 8R/8RT/8RX model year 2022 9R/9RT/9RX (with CommandView 4 cab) with Premium or Ultimate cab packages. NOTE: Compatible with boss mounts in ROPS, CommandARM mount (BRE10501), or T-slot ball (BRE10482). NOTE: See installation instructions (R567079). |
| BRE10502 | Auxiliary camera input kit for touchscreen radio Provides hardware and necessary cable to allow remote video camera to connect to touchscreen radio. NOTE: Connector cable is installed under the outer rear cab access cover with the other video connection inputs used with the CommandARM display. Video camera not included. NOTE: Compatible with BRE10364. NOTE: Compatible with model year 2020 and newer 7R and 8R/8RT/8RX model year 2022 9R/9RT/9RX with Premium or Ultimate cab packages. NOTE: See installation instructions (RE594889). |
|
|
Last Updated : 30-Nov-2021 |
| |
| |